nsainteriors.blogg.se - How to install bakor low slope roofing system

#HOW TO INSTALL BAKOR LOW SLOPE ROOFING SYSTEM PLUS#
#HOW TO INSTALL BAKOR LOW SLOPE ROOFING SYSTEM FREE#

Continue installation maintaining a minimum 3" overlap between runsħh.

#HOW TO INSTALL BAKOR LOW SLOPE ROOFING SYSTEM PLUS#

Horizontally install SlopeShield Plus underlayment across roof, starting at the bottom of the roofĦh. Install metal flashing (by others) over SlopeFlashingĥh. Install SlopeFlashing on roof gables, extending underlayment down and shingling over wall membrane, if required for air barrier continuityĤ. Install SlopeFlashing around eaves, extending underlayment down and shingling over wall membrane, if required for air barrier continuityģ. Ensure sheathing is in “as-new” conditionĢ. To prevent injury, liner should be removed from under foot as soon as membrane is installed and disposed of properlyīest Practice Horizontal Installation Instructionsġ. Please access the OSHA Web site at contact your local OSHA office, or visit the local federal bookstore to obtain the most current information on OSHA.

Where the use of ladders, scaffolds, platforms, or temporary floors are utilized, safety lines and safety harnesses shall be used.

Persons who access any roofs, involved with roof construction, repair or maintenance shall use appropriate personal protective equipment including, but not limited to, hard hats, eye protection, and leather gloves and must be trained on safe practices relevant to their work.

For roof slopes below 2:12 (9.46 degrees) contact VaproShield Technical for required approval.

Minimum recommended application temperature of 20˚F (- 6.0˚C) and rising.

SlopeShield Plus Self-Adhered Roofing Underlayment Sheet is not intended to be the primary liquid water hold out system or temporary roof covering.

SlopeShield Plus Self-Adhered should be covered within 180 days (6 months) of installation with permanent roofing material.

For Roofing Penetration Details and to ensure water and air tight details around penetrations (skylights, curbs etc.), refer to.

Avoid construction material storage on installed SlopeShield Plus Self-Adhered roof underlayment.

AVOID EXCESSIVE FOOT TRAFFIC on installed SlopeShield Plus Self-Adhered roof underlayment.

Install in an overlapping shingle fashion, with the upper courses overlapping the lower courses to shed water down the roof.

Roll underlayment with two-handed roller to ensure proper adhesion to substrate.

Pull release film and smooth out air bubbles with soft bristle push broom.

Keep SlopeShield Plus Self-Adhered membrane and release film in contact with deck as you pull the release film.

Re-roll material back to starting location with release film intact.

Align and place exposed membrane into position use hand pressure to adhere membrane to substrate.

Snap chalk lines for alignment guidance.

At bottom of roof allow for excess material to accommodate wall WRB/AB connects.

Pre-cut SlopeShield Plus Self-Adhered membrane to desired manageable lengths prior to removing release film.

Roll out material with release film intact, check for proper alignment, reposition, and align as required.

Ensure substrate fasteners are flush with surface and fastened into solid backing.

Plan the installation and layout of SlopeShield Plus Self-Adhered PRIOR to application to minimize waste.

Protect materials from direct sunlight and inclement weather until ready for use.

Store roll materials vertically on end in original packaging at temperatures between 40☏ and 120☏ (4✬ - 49✬).

#HOW TO INSTALL BAKOR LOW SLOPE ROOFING SYSTEM FREE#

Mechanical fasteners used to secure sheathing boards, insulation or penetrate roof deck shall be set flush with surface and fastened into solid backing.Īll surfaces must be clean and dry to the touch and in “as new condition ” sound, clean and free of oil, grease, dirt, or other contaminants.ĭo not install SlopeShield Plus Self-Adhered membrane when ambient temperatures are below 20☏ (-6☌) Verify that surfaces and conditions are ready to accept the work of this section. *For OSB and OSB factory-coated products contact VaproShield Technical. SlopeShield Plus Self-Adhered roofing underlayment can be installed under a variety of roofing systems including:Ĭedar Shingles/Shakes with VaproMat Drainage Matrix The underside is a fully self-adhered adhesive protected by a siliconized release film, which is removed during installation. The top coating is slip resistant and UV-stable. SlopeShield Plus Self-Adhered consists of a spun-bond polyester fabric with proprietary coatings on the top and underside utilizing Vapor Permeable Polymer Composite Technology (VPPCT™).SlopeShield Plus Self-Adhered is installed on steep slope roofs of 2:12 (9.46 degrees) or greater pitch.SlopeShield Plus Self-Adhered roofing underlayment protects the roofing assembly by allowing vapor to pass through (breathable) but not air or liquid - mitigating costly moisture damage and saving energy for the life of the building.